Ghost Immobiliser Fitting
Protect your vehicle from key theft hacking, cloning, and theft with the first aftermarket CAN immobiliser. With the option to link to an Ghost app and GPS tracking system, which can send you alerts to call if your car is tampered with or stolen.
Installing an Ghost immobiliser is a breeze for a skilled technician. It is essential to have the proper tools and heat shrink tubing.
Getting Started
Contrary to physical theft protection devices like wheel locks and car alarms, ghost immobilisers guard your vehicle without the need of key fobs or LED indicators. They are connected directly to the ECU CAN data network, and can only be activated after entering a PIN. This gives a more secure level of security against key hacking, cloning, and even ECU swapping.
Therefore, the installation of a ghost immobiliser Birmingham is a task that must be carried out with extreme agility and accuracy. It's like walking through a minefield. A single mistake could cause serious damage to your vehicle's electrical circuits. It is essential to comprehend the installation procedure and prepare your vehicle correctly.
The first step is to prepare the vehicle by taking out interior panels to make room for the immobiliser unit. Once you've found the perfect place to conceal it and secure it with cable ties to keep it from being taken away or tampered with. Clean up your wiring by tying loose wires down and using insulation tape to cover any exposed connections. This reduces the risk of a short circuit that is not intended to happen, while improving the aesthetics and reducing the chances of theft.
Finally, identify the source of constant 12V power as well as a grounding point for the ghost immobiliser. Once you've located these connections, test the power cables with a multimeter to make sure they're delivering a consistent voltage. Connect the CAN H and the CAN L wires of your immobiliser with the power source and grounding points.
Once you've made all of the connections required, it's important to double-check them and inspect the immobiliser for indications of corrosion or damage. The process of entering a PIN and launching the car is a good method of testing the system. This should be a regular part of your daily routine as it will allow you to spot any issues that may arise early. Regular testing will help extend the life of your device, and keep it functioning at its peak.
Preparing your vehicle
Installing a Ghost immobiliser requires the right expertise and tools. A wiring diagram is essential to identify the right wires, establishing precise connections and ensuring safety. A multimeter is a tool to test electrical values and ensure security. Cable tie and insulation tape can be used to secure the connections and prevent being tampered with. A user's manual will provide specific guidance tailored to your Ghost Immobiliser model.
Once installed, a ghost immobiliser is able to stop an unauthorised engine from starting by requiring the driver to input a unique PIN code sequence using buttons on the steering wheel or centre console. This can be accomplished manually or remotely using the mobile phone app and the code can be altered by the owner of the vehicle at any time. The device is also silent and is undetectable by thieves because it doesn't emit any radio frequencies.
Ghost immobilisers are directly connected to the CAN bus of the vehicle, a network that communicates with the electronic control units (ECUs) of the vehicle. It intercepts the signals transmitted by ECUs and shuts down the engine if a false signal is identified. The system is weatherproof and tamperproof. It does not have LED indicators or keys to attract thieves' attention.
It can be placed behind the dashboard or in a discreet area, so that it is not visible to thieves and doesn't hinder the vehicle's performance. It could even be placed inside a small, compact box which makes it less likely to be found during an inspection by unscrupulous car salespeople.
Its stealthy operation, along with its integration into the vehicle's CAN-bus system is a powerful deterrent to modern vehicle theft techniques such as signal relay attacks and key copying. Combining the system with other security measures will create a powerful barrier that can deter even the most persistent thieves. A growing number of insurance companies are recommending or require ghost immobilisers as they can lower the cost of insurance.
Making the Connections
Unlike traditional security systems that can be heard by thieves, ghost immobilisers are silent and prevent them from knowing when your vehicle is turned on. They also block high-tech methods of theft, such as OBD hacking. They can also be put in without causing permanent marks in your vehicle making them a good choice for people who plan to sell their vehicle in the near future.
The Autowatch Ghost 2 is a CANbus immobiliser that is among the most reliable and advanced solutions to protect your car from theft. It uses the CAN data network to shut down your engine and generates a pin code that only you know, so it is difficult for thieves to identify. It can be fitted in many vehicles and works with many existing features, including car alarms and GPS trackers, steering wheel locks, and door lock bypass systems.
If you choose to install a Ghost immobiliser, be sure to consult the wiring diagram of your specific car model to identify the wires that need connecting. Verify their positions to make sure they are accurate, and label them or tape them to help remember them. It is also necessary to locate a constant power source (12V) for the system as well as the grounding. Once you have these in place, you can start making the connections to complete the installation.
The ghost immobiliser will not allow your vehicle to start unless a pin code is entered through the buttons on the dashboard or steering wheel. This will stop ECU replication and other methods of vehicle theft. It can also be combined with other Thatcham approved security accessories such as alarms or tyre clips to give your car an additional level of protection.
As the UK automotive aftermarket market grows and expand, so are the options for securing your vehicle. There are so many ways that thieves can get into your car and steal it, so it's important to do all you can to prevent it from being stolen. That's why ghost immobilisers are an extremely popular option for responsible car owners.
Testing the System
The Ghost Immobiliser communicates with the vehicle's ECU using an CAN network. This prevents the engine from starting until the PIN code has been entered. This makes it difficult for thieves to steal the key fob that you use to start your vehicle, and even more difficult to disable the system by hacking its electronic.
Ghost Immobilisers can also be used together with GPS tracking devices that will help you track your vehicle and locate it if it's stolen. This feature is not an option that is commonly used in security products sold by the aftermarket, but it's a great option to increase your security and provide peace of mind knowing that your vehicle is always secure.
The Ghost-II immobiliser is not just a source of enhanced security but also a pleasant experience for the user, by getting rid of the need for additional key fobs or devices. It is simple and user-friendly PIN code entry that integrates seamlessly with your daily routine. It also has convenience features and deactivation settings that let you to temporarily disable the immobiliser to valet park or service your vehicle.
Make sure you have the tools you need and familiarise yourself first with the wiring of your vehicle. A basic set of tools can enable you to create precise connections. A multimeter can be used to verify electrical values. Insulation tape and heat-shrink tubing are vital to protect connections from short circuits. Cable ties can be used to secure wiring. It is also essential to be in a well-lit space and wear the appropriate safety equipment when working with tools and electrical components.
You should test the Ghost immobiliser after having completed the installation to ensure it's functioning properly. First, you need to try to start the vehicle without entering the PIN code. If ghost immobiliser 2 doesn't work, you will need to retest and inspect the connections more thoroughly.
Unlike other security systems, unlike other security systems, the Ghost Immobiliser is a covert device that is not spotted by thieves and is much more effective than traditional physical deterrents such as wheel clamps or steering locks. It is TASSA approved and recognised by some insurance companies, which makes it an investment that's cost-effective and can give you the peace of mind that you want.